JIS A5525-1994 Steel pipe piles
|
ID：
|
512B58D6FCF24E5EBCD05B4DC8E85E56
|
|
文件大小(MB)：
|
1.86
|
|
页数：
|
9
|
|
文件格式：
|
pdf
|
|
日期：
|
2009-10-26
|
|
购买：
|
购买或下载
|
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
'.,JS~,r,589-6 C3050 ~16000E,~t,1,~iRJIi JIS J\:/"7'Y~,??II,B*mm1a~,HANDBOOK,Ferrous Materials &Metallurgy II,Steel Bars, Slections, Plates, Sheets and Strip,Steel Tubular Products,Wire Rods ;and Their Secondary Products,2000,Japanese Standards Association,-G 3194-,Attached Table 1 (concluded),JIS A 5525,(1""),--.--.-- .-.. - ------ .-.. - -.--.- - - -..--.- .-.. - ,m' ,. -- =' ,. -- ,.' ,. - - =' - - - - ,. " 125 ".00 31.4 .. ISO 54.00 ".' .. 125 SO.OO ".2 os 100 OS.OO 35.'," ISO ".00 37.7 .. 180 ".80 SO., .. ISO 00.00 47.1 os l2S 36.25 M.'," 230 73.60 57.8 .. 200 72.00 36.S .. 180 72.00 36.S os ISO 67.50 53.'," 2SO 80.00 62.?.. 230 82.80 65.' .. 200 80.00 62 .?os 180 81.00 .," 280 ".00 7SO 126.' . .. 120.' ".2 os >SO 157.5 120," OSO 144.0 113 .. 144.0 113 .. >SO 140.0 II' os 180.0 lOl," SOD 160.0 126 .. OSO 162.0 127 .. .. 160.0 126 os OSO 202.5 159 7; %7.00 21.2 .. SOD 180.' lOl .. .. .. OSO 180.0 lOl os SOD 225.' lT1 ".' 25.' .. 75 30.00 23.' .. .. SOD 200.' 157 100 ".00 28.' .. .. .. ".00 28.' os 75 33.75 26.S 125 OS.OO 35.' .. 100 ".00 31.4 os .. ".S 31.8,Steel pipe piles,1: Scope This Japanese Industrial Standard specifies the welded steel pipe,plies (hereafter referred to as "piles"), used in the foundation of structures such,as civil engineering woru and architecture.,Remarks 1. The piles for landslide determent are included.,2. The standards cited in this Standard are shown in Attached,Table 1.,Informative reference: The seamless steel pipes and the centrifugally cast,steel pipes for landslide determent are. specified in,JIS G 3444 and JIS G 5201 re.pectively.,2. Classification and symbols The piles shall be cl88sified in two and their,symbols shall be 88 given in Table 1.,Table 1. Symbols for classes,Symbol for class,SKK 400,SKK 490,Informative reference,Traditional .ymOOI,SKK41,SKKSO,3. ~onstitution of .pile ~nd designation of each part of pile The constitution,of a pIle and the deSignatIon of each part of a pile shall be as follows:,(1) The pile shall comprise a single pipe or a combination of single pipes and,the designation of each part of pile shall be as shown in Fig. 1.,Fig. 1. Constitution of pile and designation of each part of pile,?Shop ciroumf.~ntial w.ld~,} SI. pipo,u,po Blank pipe,I?Site circumferential weld ~le Blank pipe [,?Site d=mfonntial wold ?N. J~ Blank pipe } Si. pipo,--~~ Blank pipe ).~~ Shop c:in:umferential weld pi"- Blank pipe,Blank pipe,-872- -873-,-A 5525- -A 5525-,(1) Welding materials used for the shop circumferential weld to connect blank,pipes into a single pipe and for mounting the accessories shall have a,ten8ile strength not less than that of the materials for the blank pipes and,accessories and meet the requirements of one of the following standards:,JIS Z 3211,JIS Z 3212,JIS Z 3312,JIS Z 3313,JIS Z 3351,J!S Z 3352,(2) A blank pipe is defined 8S a pipe produced by arc welding or electric,resistance welding from a steel strip or a steel plate. A single pipe is,de~ 8S a blank pipe as it is or blank. pipes jointed by circumferential,welding at shop.,Further, the seam weld of blank: pipes shall be welded with not les8 than,+of the circumference of the pipes shifted out of place.,(3) When blank pipes are to be welded together at site, the upper side, the,middle side and the lower side of single pipes shall be called the upper pile,the middle pile and the lower pile, respectively. In the case where the,middle pile consists of two or more pipes, they are defined 8S the first,middle pile, the second middle pile and 80 on from the lowest side upward.,4. Chemical composition The blank pipes shall be tested in accordance with,9.1 and their ladle analysis values shall be as shown in Table 2.,6. Welding materials and accessories,shall be as follows:,Welding materials and acceuories,7. Shapes, dimensions. mass and tolerances,Fig. 2, Shapes of both ends of pile and site circumferential weld,(1) Head part and tip part (2) Site circumferential weld,(1) The shapes of both ends of pile and site circumferential weld shall be as,shown in Fig. 2. When the pipes different in thickness are to be connected,they shall be preliminarily worked at shop as shown in Fig, S, 8S a rule. IT,especially required, reinforcement or work may be determined by agreement,between the parties concerned with delivery.,The shapes of the piles shall be a8 follows:,The materials used for accessories shall be equal or superior to those of 58,400 in JIS G 3101.,7.1 Sha……
……